s yb60 series single phase glass p assi va ted bridge rectifiers v oltage range - 200 to 1000 v olts current - 0.8 ampere case : molded plastic body t erminals : plated leads solderable per mil-std-750, method 2026 polarity : polarity symbols marked on case mounting position : any w eight :0.04 ounce, 1.0 grams fe a tures mechanica l d at a dimensions in inches and (millimeters) maximum r a tings and electrica l characteristics 15 75 -55 to +150 -55 to +150 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 syb 2 0 0.8 ideal for printed circuit board reliable low cost construction utilizing molded plastic technique high temperature soldering guaranteed: 260 */ 10 seconds at 5 lbs., (2.3kg) tension small size, simple installation leads solderable per mil-std-202, method 208 high surge current capability ratings at 25 * ambient temperature unless otherwise specified. single phase half-wave 60hz,resistive or inductive load, for capacitive load derate current by 20%. vo l ts vo l ts vo l ts symbols units amps amps v olts v rrm v rms v dc i f( a v) i fsm maximum repetitive peak reverse voltage maximum rms voltage maximum dc blocking voltage maximum average forward rectified current at t a =30 * on glass-epoxy p .c.b. on aluminum substrate peak forward surge current, 8.3ms single half sine-wave superimposed on rated load (jedec method) maximum instantaneous forward voltage drop per leg at 0.4a maximum dc reverse current t a =25 * at rated dc blocking voltage t a =100 * t ypical junction capactiance per leg(note3) t ypical thermal resistance per leg operating temperature range storage temperature range c j r ja t j t stg i r v f ua ua 1.0 35 5.0 100 * * s mt syb 6 0 syb 4 0 syb80 syb100 pf * /w + .193(4.90) .177(4.50) .157(4.00) .142(3.60) .276(7.0) max .102(2.60) .087(2.20) .033(0.84 .022(0.56) . 1 18(3.0) max .106(2.70) .090(2.30) .008(0.20) max .053(1.53) .037(0.95) .083(2.12) .043(1.10) .043(1.10) .028(0.70) .014(0.35) .006(0.15) * www.shunyegroup.com.cn
r a tings and characteristic c u r ves 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 0 20 40 60 80 100 120 140 160 35 30 25 20 15 10 5 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.1 1 10 100 200 reverse vo lt age.(v) fig. 3-typica l fo r w ard vo lt age characteristics per leg number of cycles fig. 2-maximum non-repetitive peak fo r w ard surge current perleg fig. 1- der a ting cu r ve output rectified current for d e i f i t c e r d r a w r o f e g a r e v a ) a ( t n e r r u c s u o e n a t n a t s n i d r a w r o f ) a ( t n e r r u c ) f p ( . e c n a t i c a p a c n o i t c n u j ) a ( . t n e r r u c e g r u s d r a w r o f k a e p ins t an t aneous fo r w ard vo lt age .(v) 1 100 1 0 1 0. 1 0.0 1 30 25 20 15 10 5 0 0 20 40 60 80 100 1 0 0 10 1 0.1 0.01 percent of r a ted peak reverse vo lt age(%) fig. 4-typica l reverse leakage characteristics per leg e g a k a e l e s r e v e r s u o e n a t n a t s n i ) a u ( . t n e r r u c ambient temper a ture,( * ) 10 fig. 5-typica l junction ca p acti t ane per leg t j =15 0 * t j =2 5 * glass epoxy p .c.b. aluminum substrate t a=40 * single half sine- w ave (jedec method) 1cycle f=50hz f=60hz t j =2 5 * pulse width=30 0 * s 1% duty cycl e t j =125 * t j =25 * t j =25 * f=1.0mh z vsig=50mv p-p www.shunyegroup.com.cn
|
